in fast mode (pin MODE = high) and 0.03 degrees rms (1 sigma) *1 in slow mode (pin MODE = low or
(1 sigma)
AS5045
Data Sheet
17.2 Transition Noise
Transition noise is defined as the jitter in the transition between two steps.
Due to the nature of the measurement principle (Hall sensors + Preamplifier + ADC), there is always a certain degree
of noise involved.
This transition noise voltage results in an angular transition noise at the outputs. It is specified as 0.06 degrees rms
*1
open).
This is the repeatability of an indicated angle at a given mechanical position.
The transition noise has different implications on the type of output that is used:
Absolute output; SSI interface:
The transition noise of the absolute output can be reduced by the user by implementing averaging of
readings. An averaging of 4 readings will reduce the transition noise by 6dB or 50%, e.g. from 0.03°rms to
0.015°rms (1 sigma) in slow mode.
PWM interface:
If the PWM interface is used as an analog output by adding a low pass filter, the transition noise can be reduced
by lowering the cutoff frequency of the filter.
If the PWM interface is used as a digital interface with a counter at the receiving side, the transition noise may
again be reduced by averaging of readings.
*1
: statistically, 1 sigma represents 68.27% of readings, 3 sigma represents 99.73% of readings.
17.3 High Speed Operation
17.3.1 Sampling Rate
The AS5045 samples the angular value at a rate of 2.61k (slow mode) or 10.42k (fast mode, selectable by pin
MODE) samples per second. Consequently, the absolute outputs are updated each 384μs (96μs in fast mode).
At a stationary position of the magnet, the sampling rate creates no additional error.
Absolute Mode
At a sampling rate of 2.6kHz/10.4kHz, the number of samples (n) per turn for a magnet rotating at high speed can be
calculated by
n slow mod e =
n fast mod e =
60
rpm ? 384 μ s
60
rpm ? 96 μ s
The upper speed limit in slow mode is ~6.000rpm and ~30.000rpm in fast mode. The only restriction at high speed is
that there will be fewer samples per revolution as the speed increases (see Table 2 ).
Regardless of the rotational speed, the absolute angular value is always sampled at the highest resolution of 12 bit.
www.austriamicrosystems.com
Revision 1.7
28 – 33
相关PDF资料
AS5134 PB BOARD PROGRAM AS5134
AS5140 PB BOARD PROGRAM AS5140
ASDMB-ADAPTER-KIT ASDMB MEMSPEED P II OSC KIT
ASFLMPLP-ADAPTER-KIT ASFLMPLP MEMSPEED P II OSC KIT
AT24C01-10SI-1.8 IC EEPROM 1KBIT 400KHZ 8SOIC
AT24C01B-TSU-T IC EEPROM 1KBIT 1MHZ SOT23-5
AT24C02C-XHM-B IC EEPROM 2KBIT 1MHZ 8TSSOP
AT24C04AN-10SI-2.7 IC EEPROM 4KBIT 400KHZ 8SOIC
相关代理商/技术参数
AS5045_V1 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:12 Bit Programmable Magnetic Rotary Encoder
AS5045-AB 制造商:ams 功能描述:AS5045 Adapter Board
AS5045-ADAPTER 制造商:AMS 功能描述:Adapter Board to Test and Evaluate AS5045 Rotary Encoder
AS5045ASST 制造商:ams 功能描述:T&R / SSOP 16
AS5045-ASST 功能描述:IC ENCODER PROG 12-BIT 16-SSOP RoHS:是 类别:传感器,转换器 >> 磁性 - 霍尔效应,数字式开关,线性,罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出(最大):- 输出类型:数字式,PWM,8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP(0.209",5.30mm 宽) 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR
AS5045ASSU 制造商:AMS 功能描述:IC MAGNETIC ROTARY ENCODER 12BIT SSOP16 制造商:AMS 功能描述:IC, MAGNETIC ROTARY ENCODER 12BIT SSOP16 制造商:AMS 功能描述:IC, MAGNETIC ROTARY ENCODER 12BIT SSOP16; IC Function:Encoder IC; Brief Features:360 Contactless High Resolution Angular Position Encoding, Two 12-bit Absolute Output; Supply Voltage Min:3V; Supply Voltage Max:3.6V; No. of Pins:16 ;RoHS Compliant: Yes
AS5045-ASSU 功能描述:板机接口霍耳效应/磁性传感器 RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点(Brp):- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23
AS5045B 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:12-Bit Programmable Magnetic Position Sensor